Mbm-corporation 430 EP semi-automatic programmable Manual de usuario

EBA 430 EEBA 430 EPEBA • Made in Germany • EBA Krug & Priester • 72336 Balingen • Germany • www.eba.de •Document ShreddersTri

EBA 430 E • EBA 430 EPBAC-19-A-18-Optical cutting line (A) that indicates the exactposition of the cut.(Only use when no exact cutis required).Only fo

EBA 430 E • EBA 430 EPcminch-21--20-AABefore every cut the lever must be pushed tothe left and tightened with light pressure.Press both buttons of the

EBA 430 E • EBA 430 EP-23--22-cminchcminchEBA 430 EPStart machine• Main switch F to position "I", insert the key Hfor the control panel and

EBA 430 E • EBA 430 EP-25-cminch-24-cminchProgrammingonly EBA 430 EPThis control system enables you to store 9programs with 9 programmable steps. One

EBA 430 E • EBA 430 EP-27-1.2.-26-If the cutting quality decreases:• Check the cutting depth (see page 34).• Check the cutting stick (see page 30).• R

EBA 430 E • EBA 430 EP-29-1.2.1.3.2.-28-BAThe 3 eccentrics are now exposed and shouldbe turned counter clockwise to position "0"with the spe

EBA 430 E • EBA 430 EP-31-4-5 mm0.15-0.20 inchCABB1.2.-30-1.2.3.If needed the cutting stick can be turned orexchanged. (The cutting stick can be usede

EBA 430 E • EBA 430 EP2.1.-33-2.1.3.5.A4.3.1.2.-32-Lightly tighten 3 of the 5 blade screws (1.)(with washers), remove the blade changingtool (2.) and

EBA 430 E • EBA 430 EP-35--34-AADBEFCCut a stack of paper to test. If the last sheet hasnot been cut through move the knob for theadjustment of the bl

EBA 430 E • EBA 430 EP-37-BA-36-Safety checkAccording to § 40 VBG 7i a safety checkaccording to the safety stipulations has to bemade every 5 years by

EBA 430 E • EBA 430 EP-3-EBA 430 E • EBA 430 EP-2-Dear customer,Thank you for choosing a paper cutting machine from EBA. With the purchase of thisqual

EBA 430 E • EBA 430 EPBCA-39--38-ABMachine turns off:EBA 430 E and EBA 430 EP• Extreme load of machine (cooling phase.Security switch (A) turns off.Ab

EBA 430 E • EBA 430 EP-41-cminchEBA"Service"CBAD-40-Motor runs but blade does not movedownwards.• Security brake has been activated!Inform t

EBA 430 E • EBA 430 EP-43-EBA"Service"-42-None of the above mentioned methodshelped to solve the problem:Contact Service team under• www.EBA

EBA 430 E • EBA 430 EP-45--44-Wolfgang Priester-General Manager-Remarks:MANUFACTURER’S DECLARATIONThis machine is approved by independentsafety labor

EBA 430 E • EBA 430 EP-5--4-Children must not operate the machine!Do not cut hard materials or materials whichmay splinter!The machine must not be loc

EBA 430 E • EBA 430 EP-7--6-Never leave the blade unattended. Do notdismount or transport the blade withoutprotection!Risk of injury! The machine may

EBA 430 E • EBA 430 EPBABCA≤15mm≤0.59inch-9--8-AAABACCOperating the machine without safety device(front safety guard (A), rear screwed safetyguard (B)

EBA 430 E • EBA 430 EP-11--10-230 V / 10A min115 V / 15A minProtect mains cable against heat, oil andsharp edges!Connect the power cord to a single ph

EBA 430 E • EBA 430 EP-13-CAB-12-1.2.3.Unpack the cabinet (A), (accessories) or stand(B), (accessories) and assemble accordingto the enclosed separat

EBA 430 E • EBA 430 EP-15-BACDAAABBCD-14-It is not allowed to operate the machine if theoperating and safety instructions have notbeen understood. Ple

EBA 430 E • EBA 430 EPBCAEBA 430 EEBA 430 EP-17--16-ABDEEBA 430 EEBA 430 EPCEBA 430 EThe backgauge has to be adjusted by thehandle with calibration ri