Mbm-corporation iCREASE EXCEL Manual de usuario

icreaseEXCEL Digital Creaser Operators Manual 2-2013 Version 1.0 6-2013 Version 3.0 WWW.MBMCORP.COM 800-223-2508

TRANSPORT OPERATION  The Run Button will start the Transport in any given mode. Press it again to stop the transport. Each Mode has a t

Tri-Fold: Press the Crease Mode Button > Tri-Fold > Start Measuring > Physically Run a sheet through the machine for the sensor to measure &g

Gate Fold: Press the Crease Mode Button > More > Gate > Start Measuring > Physically Run a sheet through the machine for the sensor to me

Perfect Bind Single Hinge: Press the Crease Mode Button > More > Perfect Binding Score > Enter The Book Thickness > Single Hinge > Star

Saving Custom Crease Jobs: Press the Crease Mode Button > Custom > Enter In Distance For each Crease in mm > Save > Select Position to sav

Batch Counter: Press the Batch Counter button from the run screen in any mode and it will take you to the Batch Count Screen. Press the Enter Batc

FEED TABLE ASSEMBLY Nut –Adjustment Feed – F-0640 Micro-Lateral Adjustment Lock – F-0645 When positioning is correct, this will lock

ADJUSTING THE FEED RAILS The feed rails on your icreaseEXCEL are designed to adjust easily in case of a problem with crooked feeding. By loosening t

SETTING THE AUTOMATIC FEEDER For efficient Auto-feeding, the setting of the feed wheels is very important. Use a piece of the stock to be run as a “f

LOADING THE FEEDER Take the fanned paper and load the feed tray as shown. The leading edge of the top sheet is slightly forward of the one below and s

TABLE OF CONTENTS SPECIFICATIONS…………………………………………………………………………………………….1a SAFETY PROCEDURES/CARE & MAINTENANCE.………………………………………………….1b COMPONENT IDENT

REPLACING THE FRICTION PLATE The contact strip below the feed wheels is a consumable part. If this strip begins to show excessive wear, or additional

PERF SHAFT & STRIKE PLATE A – Support Bar – F-0232 This is the shaft that the roller wheels and perf score are mounted o

PERFORATING AND SCORING ASSEMBLIES For removing and old blade and attaching a new blade to the pressure adjust mounting bracket, remove the (1) butto

GRIPPER WHEEL PERF-SCORE MOUNTING Position your score blade as desired. Scores should be made so that the blade runs on the side of t

RAC System (Rotary Actuated Creasing) Assembly Component ID A. RAC drive motor B. Eccentric Drive Shaft C. Upper crease die D. Pressure Adj

ADJUSTING THE RAC ROLLERS The RAC rollers are set from the factory and it is NOT recommended to make any adjustments to this without consulting with

 POWER DOES NOT TURN ON 1. Check circuit breaker on rear panel. 2. Check outlet for power.  POWER TURNS ON BUT HMI DOES NOT LIGHT UP 1

ELECTRICAL REQUIREMENTS AND SPECIFICATIONS Power Requirement: 110/220V, 50-60 HZ, AC, Circuit Protection: 3 AMP Circuit Breaker NOTE: Ol

SAFETY PROCEDURES BEFORE USE:  Read through the owner’s manual. Follow instructions CAREFULLY.  NEVER use a wet area. Electric shock could occur

COMPONENT IDENTIFICATION REFERENCES 2 Feed Table Assembly Touch Screen Delivery Tray Perf and Score Assemblies Crease

SETTING UP YOUR icreaseEXCEL STAND (optional) 1. Open top of box and remove components. 2. Assemble stand. (See Directions) 3. Place machine on st

icreaseEXCEL TOUCH SCREEN CONTROLLER THE TOUCH SCREEN CONSISTS OF FOUR SECTIONS: 1. MBM Logo and Service Access 2. Perf Mode

Perf Mode From the home screen press the perf mode button the perf mode screen will be displayed. Home: Takes you back to the home screen. Counter R

Feeder Mode Feed mode is the mode to run your icreaseEXCEL as a feeder into our CountCoat UV Coater. It runs much slower than the other modes giving